DynamicConnector Properties

Field Value

Type: 
Defines the manner in which objects align to each other when snapped together.

Field Value

Type: 
List of connector Types that are allowed to connect with this connector. If empty then all connectors are allowed, as long as they are not named explicitly in the Disallowed list.

Field Value

Type: 
Indicates whether this connector allows inbound transfers, i.e., TransferDirection == In or InOut.

Field Value

Type: 
Indicates whether this connector allows outbound transfers, i.e., TransferDirection == Out or InOut.

Field Value

Type: 
If true, then the visual will reconfigure the connector to the built-in defaults upon reset. Set this to false if you have modified one of the built-in connectors (for example, "Start" on a conveyor).

Field Value

Type: 
If true then connector will snap to other connectors with AutoConnect enabled when brought close together (see also SnapDistance)

Field Value

Type: 
The horizontal offset perpendicular to the connector.

Field Value

Type: 
Mid-point between Start and End locations in the visual's space.

The first connector this connector is connected to, or null if no connected at all.

Field Value

Type: 
If connected then this is the effective location of the connection in world coordinates.

All connectors that are connected to this one.

Field Value

Type: 
If true, then the control point will be shown to indicate location, name and orientation of this connector.

Field Value

Type: 
Size of the control point, when enabled.

Field Value

Type: 
List of connector Types that are not allowed to connect to this connector. If a Type appears in both Allowed and Disallowed, then Disallowed takes priority, and the Type is disallowed.

Field Value

Type: 
Location of end extent of the connector. The distance from Start to End defines the connector's width.

Field Value

Type: 
The vertical offset perpendicular to the connector.

Is this connector connected to other connectors?

Field Value

Type: 
With AutoConnect=True, then the snapping action also allows the visual with the shortest connector (distance from Start to End) to slide along the length of the longer partner connector (on the other visual). The KeepInBounds property (of the longer connector) defines whether the longer connector will allow the shorter connector to extend its length beyond the length of the longer connector.

Get the length of the connector.

Optional limit to the number of connectors that this connector can connect to. This is int.MaxValue by default making it effectively unlimited.

The name of the connector.

Field Value

Type: 
Direction of the connector.

Field Value

Type: 
When true, the owning visual will be reparented to the partner connector's owning visual. This is useful for creating components such as interchangeable robot end-effectors, which need to become part of the robot component when snapped into position.

Field Value

Type: 
When true, in Linear Physics, a virtual sensor and stop blade are added to the ongoing conveyor that this conveyor will merge into via this outgoing connector. This enables a simple level of overlap avoidance without adding in explicit sensors and stops by hand.

Field Value

Type: 
In Linear Physics, this indicates the motor visual to use for the transfer speed of loads. If not set then it defaults to conveyor that owns the connector.

Field Value

Type: 
In Linear Physics, if SimulationTransferEnabled is true, this extends the sensor on the next conveyor back this distance. This allows the next conveyor to act as a main line and not block while a load is being transferred from this conveyor.

Field Value

Type: 
In Linear Physics, if the angle between two conveyors is less than this number then the load will transfer be in the same orientation it is in on the current conveyor. If the angle is greater than this number then the load will be rotated by 90 degrees. Set this to 180 to prevent loads rotating from their current orientation. The default is 80 degrees.

Field Value

Type: 
In Linear Physics, if not zero, this value overrides the width of the outgoing conveyor for the transfer zone size.

Field Value

Type: 
Distance at which AutoConnect (if set to True) will come into effect.

Field Value

Type: 
Location of start extent of the connector. The distance from Start to End defines the connector's width.

Field Value

Type: 
Height of the text label on the connector.

Field Value

Type: 
Used by the Transfer protocol (as implemented in many QuickStart components) to define in which direction this connector allows transfers to take place. A value of "In" means that the component receive loads on this connector. A value of "Out" means that the component will deliver loads on this connector. A value of "InOut" means the component will receive and deliver loads on this component. A value of "None" means that the component will neither receive nor deliver loads on this connector. For example, "Start" connectors usually have this property set to "In"; "End" connectors usually have it set to "Out"; "Left" and "Right" connectors might have it set to "InOut"; connectors that are used for snapping end-effectors (for example) would have it set to "None", since they are not used for transferring loads. The component will consider the TransferDirection of the partner connector to find the effective TransferDirection; for example, if this connector is set to "In", then the other connector must be set to "Out" or "InOut" for a transfer to be possible.

Field Value

Type: 
Optional type value that allows the connector to be identified in the Allowed and Disallowed properties of other connectors

Get the center of the connector in world coordinates

Get the end of the connector in world coordinates.

The world normal of the connector.

Get the start of the connector in world coordinates.